AMX TV Receiver CB MVP WCS52 User Manual

Installation Guide  
CB-MVP-WCS52  
Rough-In Box for MVP-WCS-52 Wall Charging Station  
Note: Ensure that the Rough-In Box is flush with the 2x4 studs. Any overhang  
will affect the installation of the covering sheetrock, as well as affect the  
placement of the Plastic Back Box. The Rough-In Box has two sets of knockouts  
in the top and bottom, one of the set for US wiring and one for international  
wiring.  
Overview  
The CB-MVP-WCS52 Rough-In Box allows the MVP-WCS-52 (5.2" Modero  
ViewPoint Wall Charging Station) to be installed in a solid surface (e.g., wall or  
podium).  
Note: Make sure that the power cable has been pulled through the Rough-In  
Box by the resident electrician before continuing the installation.  
Specifications  
CB-MVP-WCS52 (FG037-11) Specifications  
After completing the installation of the Rough-In Box, install sheet rock or other  
wall material over the box, cut a hole matching the size of the inside diameter in  
the sheet rock, and clean out all dust before proceeding with the installation of  
the plastic back box.  
Dimensions (HWD):  
Certifications  
• 5 11/16" x 8 3/8" x 1 1/2"  
• 144.4 mm x 212.2 mm x 38.1 mm  
• cTUVus Listed  
WARNING: INSTALLER, LEAVE A GAP BETWEEN THE STUD AND  
ROUGH-IN BOX TO ACCOMMODATE THE DRYWALL/SHEETROCK.  
This gap allows the installation of the drywall/sheetrock after the  
CB-MVP-WCS52 has been mounted onto the beams. The stud notching and  
Rough-In Box installation must be done prior to any wall installation.  
Note: The most important thing to remember when mounting this Rough-In Box  
is that the mounting tabs must be mounted flush against the outside of the  
sheetrock. This step determines whether or not the mounting stud is notched  
(cutout-out to fit the Rough-In Box).  
Installing the CB-MVP-WCS52  
The CB-MVP-WCS52 Rough-In Box is 10 inches (25.40cm) wide at its widest  
dimension (wider than the bezel of the Wall Charging Station), and is only  
intended for pre construction installations (FIG. 1). Refer to SP5966-01 for  
detailed dimensions and installation specifications (see reverse)  
The Rough-In Box is used in conjunction with the Wall Charging Station’s plastic  
back box.  
The Rough-In Box must be located behind 3/8" (0.95cm) to 3/4" (1.91cm) of wall/  
mounting surface material.  
Install front surface of  
Rough-In Box flush with  
surface of wall stud  
FIG. 1 Typical CB-MVP-WCS52 Installation  
The Rough-In Box bears a wing on each corner which is intended to bridge gaps  
between studs and/or spacers. These wings may be bent carefully in order to fit  
a particular gap, but may not be so bent as to allow the box to hang in a vertical  
position.  
FIG. 2 Installation of Wall Unit  
Once placed in the desired position, put at least one screw through each wing  
into the adjoining stud or spacer to secure it.  
The interior of the Rough-In Box contains a set of holes on either side, as well as  
top and bottom, for standard 1/4-inch screws. Use these holes to anchor the box  
to its adjoining studs or spacers.  
 
 

3Com Network Router 3CRWE53172 User Manual
Aastra Telecom Telephone 8009 User Manual
Addonics Technologies Network Card ST5BDVES User Manual
Agilent Technologies Recording Equipment E6432A User Manual
Amana Air Conditioner AP076E User Manual
Amana Range 8113P765 60 User Manual
Amcor Air Conditioner PORTABLE AIRCONDITIONER User Manual
American Standard Hot Tub 2645L User Manual
BB Electronics Switch EIR505 XX User Manual
Behringer Car Amplifier SX3282 User Manual