AG Neovo Universal Remote ATP AST Series User Manual

Analog Resistive Touchscreen  
ATP/AST Series Product Specifications  
 
ATP/AST Series Product Specifications  
1. Product Specifications  
1-1. Product Applicable  
§ This specification is applied to the analog resistive touchscreen: ATP/AST Series.  
1-2. Structure  
§ Dimensions, structure, and shape are referred on the drawing attached.  
1-3. Environmental Specifications  
Specification  
Value  
Operating Temperature  
-20°C to 70°C (no condensation)  
-20°C to 60°C Less than 90%RH (no condensation)  
Exceeding 60°C 133.8g/m3 (no condensation)  
-40°C to 80°C (no condensation)  
Operating Humidity  
Storage Temperature  
Storage Humidity  
-40°C to 60°C Less than 95%RH (no condensation)  
Exceeding 60°C 142.9g/m3 (no condensation)  
Toluene, Tricholoroethylene, Athetone, Alcohol,  
Gasoline, Machine Oil, Ammonia, Glass Cleaner,  
Mayonnaise, Ketchup, Wine, Salad Oil, Vinegar, Lipstick, etc.  
Chemical Resistance  
(top surface)  
1-4. Mechanical Characteristics  
Specification  
Value  
Activation Force  
0.05N to 0.8N  
Input (finger)  
Character Input (pen)  
10,000,000 hits  
Operating Life  
100,000 characters  
Light Transmittance  
Surface Hardness  
Over 80% (typical value at full wavelength)  
Over 2H (by JIS pencil hardness)  
1-5. Electrical Characteristics  
Specification  
Value  
Maximum Voltage  
DC6V  
Top Electrode  
100mA  
100mA  
0.5mA  
Maximum Current  
Bottom Electrode  
Between the Top and Bottom  
Linearity  
Under ±2% (Under ±1% (typical value))  
Top Electrode  
Less than 1kΩ  
Less than 1kΩ  
Terminal Resistance  
Bottom Electrode  
Neighboring Terminals  
Active Area Electrodes  
Over 20MΩ at 25V  
Over 20MΩ at 25V  
Insulation Resistance  
Chattering  
Less than 10msec at ON/OFF.  
3
Rev. 10©1999 - 2006 DMC Co., Ltd.  
 
ATP/AST Series Product Specifications  
1-6. Appearance  
§ Scratch, dust (W = width, L = length, D = average diameter = (longest + shortest) /2)  
Item  
Width (mm)  
0.1W>0.05  
0.05W>0.03  
0.03W  
Length (mm)  
4L  
Acceptable Numbers  
1pcs in φ30mm  
2pcs in φ20mm  
Acceptable  
Total  
Scratch  
10L  
20L  
0.1W>0.05  
0.05W  
5L  
2pcs in φ30mm  
Acceptable  
Dust  
Within 5pcs per  
product.  
(Linear)  
Acceptable  
1pcs in Viewing Area *1  
2pcs in φ30mm  
Acceptable  
0.4D>0.3 *1  
Dust  
0.3D>0.2  
0.2D  
(Circular)  
Applied only in the Active Area. Scratches or dusts in the outside of the Active Area are acceptable unless the  
electrical characteristics are affected.  
*1 Applied to the size of 14 inches or more.  
§ Dirt  
Acceptable if not noticeable on a black mat.  
§ Tip, crack (t = glass thickness) (applicable only for the glass)  
Item  
Size (mm)  
Acceptable Numbers  
X
Y
Z
X
Y
Z
3  
3  
t  
Z
2pcs  
X
Y
Corner  
/panel  
Y
5  
3  
t  
X
2pcs  
/side  
Side  
Z
Crack  
0pcs (acceptable)  
4
Rev. 10©1999 - 2006 DMC Co., Ltd.  
 
ATP/AST Series Product Specifications  
2. Testing Regulation  
2-1. Testing Regulation  
§ If the regulation is not specified, the test is performed under the supplier’s regulation.  
§ Tests are performed under the room temperature unless specified. The room temperature is referred as  
follows:  
Temperature: 20°C±5°C  
Humidity:  
65%±10%RH  
2-2. Environmental Specifications  
§ Chemical Resistance Test  
Condition:  
Tested after leaving the chemical on the surface for 12 hours being wiped off by cloth.  
Judgement: Must be no effect in appearance.  
2-3. Mechanical Characteristics  
§ Activation Force Test  
Condition:  
Measured by depressing the point between  
the dots to the conduction by the testing rod  
(Figure 1).  
Silicon Rubber  
(Hardness: 60°)  
Tip: R = 4.0  
Judgement: Must satisfy the specification.  
§ Operating Life Test (Finger)  
Figure 1. Testing rod 1  
Condition:  
Testing rod: Refer to Figure 1  
Voltage:  
Load:  
DC5V  
300g  
Cycle:  
2 hits/sec  
Judgement: Must satisfy the following:  
Activation Force:  
Within ±50% of the specification.  
Linearity:  
Terminal Resistance:  
Insulation Resistance:  
Must satisfy the specification.  
Must satisfy the specification.  
Must satisfy the specification.  
§ Operating Life Test (Pen)  
Condition:  
Testing rod: Refer to Figure 2  
Polyacetal resin  
Tip: R = 0.8  
Voltage:  
Load:  
DC5V  
250g  
Input size: 10 x 10 mm  
Input character: A to Z/minute  
Figure 2. Testing rod 2  
Judgement: Must satisfy the following:  
Activation Force:  
Within ±50% of the specification.  
Linearity:  
Terminal Resistance:  
Insulation Resistance:  
Must satisfy the specification.  
Must satisfy the specification.  
Must satisfy the specification.  
5
Rev. 10©1999 - 2006 DMC Co., Ltd.  
 
ATP/AST Series Product Specifications  
2-4. Electrical Characteristics  
§ Terminal Resistance Test  
Condition:  
Top and bottom electrodes are measured at the terminal.  
Judgement: Must satisfy the specification.  
§ Insulation Resistance Test  
Neighboring Terminals: Measured by applying the reference voltage to the terminals  
Active Area Electrodes: Measured by applying the reference voltage to the top and bottom electrodes.  
Judgement:  
Must satisfy the specification.  
2-5. Appearance  
§ Appearance Test  
Condition:  
Tested by an examiner with over 1.0 eyesight at 30cm away from the product under the  
transmittable light at over 60° the surface of the product.  
Judgement: Must satisfy the specification.  
6
Rev. 10©1999 - 2006 DMC Co., Ltd.  
 
ATP/AST Series Product Specifications  
3. Reliability Condition  
3-1. Temperature Condition  
§ Temperature Condition Test  
Following test are performed in the condition with no dew condensation:  
Cold Test:  
Tested after leaving the parts in -30°C±3°C for 240 hours and in the room temperature  
for 2 hours.  
Heat Test:  
Tested after leaving the parts in 80°C±3°C for 240 hours and in the room temperature for  
2 hours.  
Humidity Test: Tested after leaving the parts in the temperature 60°C±3°C, humidity 90 to 95% for 240  
hours and in the room temperature for 2 hours.  
Cycle Test:  
Judgement:  
Tested after 5 cycles of leaving the parts in the temperature -30°C±3°C for 1 hour and in  
the room temperature for 0.5 hours, then leaving the parts in the temperature 70°C±3°C  
for 1 hour and in the room temperature for 0.5 hours.  
Must satisfy the following:  
Activation Force:  
Linearity:  
Terminal Resistance:  
Within ±50% of the specification.  
Must satisfy the specification.  
Must satisfy the specification.  
Insulation Resistance: Must satisfy the specification.  
Appearance: Must satisfy the specification.  
4. Recommended Connector  
4-1. Recommended Connector  
Part No.  
Pins  
4 pin Double-sided  
Pitch  
KCA-K4R  
1.25mm  
7
Rev. 10©1999 - 2006 DMC Co., Ltd.  
 
ATP/AST Series Product Specifications  
5. Handling Notes  
5-1. Precautions  
§ This product is intended for use in standard applications (computers, office automation, and other office  
equipment, industrial, communications, and measurement equipment, personal and household devices,  
etc.) Please avoid using this product for special applications where failure or abnormal operation may  
directly affect human lives, or cause physical injury or property damage, or where extremely high levels  
of reliability are required (such as aerospace systems, vehicle operating control, atomic energy controls,  
medical devices for life support, etc.).  
5-2. Handling Notes  
§ Do not depress or scratch the product with any object with a sharp edge or end.  
§ Do not forcibly bend or fold the product.  
§ When the product is stored, make sure it is packed in a packing box and stored in a storage temperature  
range, eliminating any outside load.  
§ Do not use or store the product under a condition where the product will be exposed to water, organic  
solution or acid.  
§ Do not use the product under the direct sunlight.  
§ Do not disassemble the product.  
§ When you handle the product, Hold the product by its body. Do not hold by the tail.  
§ Clean the product with a soft cloth or a soft cloth with neutral detergent or alcohol. When contaminated  
by chemicals, wipe them off immediately with caution not to cause injury to human body.  
§ The edge of the glass is not rounded and may cause injury.  
5-3. Construction Notes  
§ The environmental specifications, mechanical characteristics, and electrical characteristics are only  
applied to the Active Area.  
§ Do not use the touchscreen when the condensation occurs. The condensation inside of the touchscreen  
is a natural phenomenon and should disappear after the touchscreen is warmed up.  
5-4. Electrical & Software Notice  
The best performance can be obtained when used with the original analog resistive touchscreen controller,  
“TSC-10” Series. If the touchscreen controller or controller software is to be developed by the customer,  
please note the following:  
§ There is a contact resistance between the top and bottom electrodes and it changes by the pressure of a  
finger or a pen. The data must be read after the contact resistance becomes stabilized.  
§ The terminal resistance of the analog resistive touchscreen varies by the individual, time, and  
environment. The controller software must have the calibration function to adjust the input position and  
the display position.  
§ The analog resistive touchscreen outputs 2 point input as 1 point in between the 2 points. The controller  
software must not be designed to have the 2 point input function.  
§ For drawing applications, the line may be intermittent when the pen comes on the dot spacers. A  
software compensation is needed.  
8
Rev. 10©1999 - 2006 DMC Co., Ltd.  
 
ATP/AST Series Product Specifications  
5-5. Mounting Notes  
Bezel  
§ Bezel Edge  
Bezel edge must be positioned in the area between the Active  
Area and the Viewing Area. The bezel may press the  
touchscreen and cause input if the edge enters the Active  
Area.  
Active Area  
Viewing Area  
§ Gap between the Bezel and Touchscreen  
Bezel  
Top Electrode  
A gap of approximately 0.5mm is needed between the bezel  
and the top electrode. It may cause unexpected input if the  
gap is too narrow.  
§ Cushion  
If a cushion is used between the bezel and the top electrode,  
the cushion must be free enough to absorb the expansion and  
contraction difference between the bezel and the top  
electrode. If the cushion is squashed too hard, the expansion  
and the contraction difference may cause the distortion to the  
top electrode.  
Bezel  
Cushion  
Insulation Area  
Top Electrode  
Minimum 1mm  
The cushion must be positioned more than 1mm outward from  
an inside of the insulation area. (Please refer to right figure)  
§ Tolerance  
There is a tolerance of 0.2 to 0.3mm for the dimensions of the  
touchscreen and the tail. A gap must be made to absorb the  
tolerance in the case and the connector.  
0.2 - 0.3mm  
Case  
§ Tail  
The tail must not be forcibly stressed or bent too hard to avoid  
the conduction in the insulated area and wire breaking.  
Tail  
Bezel  
§ Mounting  
Touchscreen must be held from the bottom such as the  
structure gluing the touchscreen onto the display. If the  
touchscreen is glued to the bezel, the adhesion between the  
top and bottom electrode is stressed and may come off.  
Display  
§ Forbidden Area  
Bezel  
The area within 2mm from the insulation area is structurally  
week for the pressure, espcially for pen use. The film may be  
forcibly bent and may cause defection. This area must be  
protected by the bezel and input must be avoided.  
§ Air Vent  
Forbidden Area  
Most of the touchscreens have the air vent to equalize the  
inside air pressure to the outside one. The air vent must be  
open and liquid contact must be avoided as the liquid may be  
absorbed if the lquid is accumilated near the air vent. The top  
electlode must not be swelled by the air pressure from inside  
of the case.  
9
Rev. 10©1999 - 2006 DMC Co., Ltd.  
 
ATP/AST Series Product Specifications  
6. Warranty  
6-1. Warranty Period  
§ The warranty period is limited to 1 year from the date of shipping. The warranty for the initial defection  
such as appearance defection is limited to 1 month.  
§ Any defected parts under proper use will be examined by the supplier and replaced by the new parts if  
the defection is considered to be caused by the supplier.  
§ The replacement is subject to be included in the next lot.  
6-2. Warranty Target  
§ The warranty only covers the product itself and does not cover any damage to others caused by using  
this product. Onsite repair or replacement is not supported.  
§ We will do our best for delivery problem and product defections, but the warranty for the production line  
is not covered.  
§ Resistive touchscreens are structurally not repairable. All defections are subject to replacement.  
6-3. Warranty Exceptions  
Following conditions are not covered with the warranty and subject to charge.  
§ Any malfunctions and damages during transportation and transfer by the user.  
§ Any malfunctions and damages caused by a natural disaster or a fire.  
§ Any malfunctions and damages caused by static electricity  
§ Any malfunctions and damages caused by the failure of the associated equipment.  
§ If the product is remodeled, disassembled or repaired by the user.  
§ If the product is glued onto the equipment and uninstalled.  
§ Any malfunctions and damages caused by an improper usage and handling against the specifications  
and notes.  
6-4. Tools  
§ To maintain the quality, the printing screens and the die-cut plates are generally limited to use up to 1  
year. Reorders after 1 year from the initial order or from the last renewal are subject to the tooling charge  
for replacing the printing screens and the die-cut plates. Reorders for the discontinued standard parts are  
also subject to tooling charge.  
§ All the tools, such as CAD data (except for the drawing for approval), block copies (films), printing  
screens, and die-cut plates are not to be provided for administrative purpose.  
6-5. Changes  
§ Because of the manufacturing process, changing the dimensions, circuit pattern, and the tail position  
requires replacing most of the tools and is subject to high tooling charge. Please be careful when  
ordering and approving the drawing.  
§ Circuit pattern and the materials that does not affect the environmental, electrical, and mechanical  
characteristics such as film, glass, ink and glue are subject to change for the supplier’s reason or for  
improvement within the specifications.  
§ Standard products are subject to change for improvement without notice.  
10  
Rev. 10©1999 - 2006 DMC Co., Ltd.  
 
ATP/AST Series Product Specifications  
7. Revision history  
Rev1 (April 15, 1998)  
Initial release  
Rev2 (June 1, 1999)  
The overall revision by specification review.  
Rev3 (April 1, 2002)  
The address in the office was changed by the move.  
Rev4 (August 16, 2002)  
1-4.Activation Force is changed “50g± 30g” to “0.5N±0.3”.  
1-4.Light Transmission is changed 76% to 80%(TYP).  
Rev5 (September 3, 2002)  
1-3.Operating Temperature is changed “0°C to 60°C” to “-20°C to 70°C”.  
1-3.Storing Temperature is changed “-20°C to 70°C” to “-40°C to 80°C”  
1-4.Operating Life is changed “1,000,000 hits” to “10,000,000 hits”.  
1-5.Linearity is changed “Under ±2%” to “Under ±1% (typical value)”.  
Rev6 (June 28, 2004)  
1-3.Operating Humidity is changed “Less than 90%RH (no condensation)” to “-20°C to 60°C Less than  
90%RH (no condensation) Exceeding 60°C 133.8g/m3 (no condensation)”.  
1-3.Storing Humidity is changed “Less than 95%RH (no condensation)” to “-40°C to 60°C Less than  
95%RH (no condensation), Exceeding 60°C 142.9g/m3 (no condensation)”.  
1-5.Maximum Voltage is changed “DC5V” to “DC6V”.  
1-5.Linearity is changed “Under ±1% (typical value)” to “Under ±2% (Under ±1% (typical value))”.  
Rev7 (October 15, 2004)  
4-4.Electrical & Software Notice: Changed “FIT-10 series” to “TSC-10 series”.  
Rev8 (April 7, 2005)  
Added Item4 Recommended Connector.  
Rev9 (September 6, 2005)  
2-3.Mechanical Characteristics: Added Operating Life Test (Pen).  
11  
Rev. 10©1999 - 2006 DMC Co., Ltd.  
 
ATP/AST Series Product Specifications  
Rev10 (November 10, 2006)  
The specification item name was changed.  
1-3.”Storing Temperature” to “Storage Temperature”  
1-3.”Storing Humidity” to “Storage Humidity”  
1-4.”Operating Load” to “Activation Force”  
1-4.”Light Transmissivity” to “Light Transmittance”  
1-4.”Top Surface Hardness” to “Surface Hardness”  
2-3.”Operating Load Test” to “Activation Force Test”  
2-3.”Operating Load” to “Activation Force”  
3-1.”Operationg Load” to “Activation Force”  
1-4.Operating Force is changed “0.5N±0.3N” to “0.05N to 0.8N”.  
1-5.Insulation Resistance is changed “Over 100MΩ at 25V” to “Over 20MΩ at 25V”.  
1-6.Tip, crack: Deleted “Applied only in the Active Area. Scratches or dusts in the outside of the Active  
Area are acceptable unless the electrical characteristics are affected.”.  
2-3. § Operating Life Test (Pen) Load: 300g to 250g  
5-5. § Cushion: Added an installation position of a cushion.  
7.Added Revision History.  
12  
Rev. 10©1999 - 2006 DMC Co., Ltd.  
 
ATP/AST Series Product Specifications  
ATP/AST Series Product Specifications  
Rev. 10, November 10, 2006  
©1999 - 2006 DMC Co., Ltd.  
This document can be freely distributed, but any alternation to this document is prohibited.  
9th floor, Kanda Sento Building, 1-2-4 Yushima, Bunkyo-Ku, Tokyo 113-0034, Japan  
Phone: +81-3-5209-7131 (Japanese), 7135 (English) Fax: +81-3-5209-7130  
13  
Rev. 10©1999 - 2006 DMC Co., Ltd.  
 

AAMP of America IP Phone PGHMZ1 User Manual
Actiontec electronic Network Router GE344000 01 User Manual
ADC Network Card 410F User Manual
Altinex Switch SW104 130 User Manual
Amerec Portable Generator 3K10 User Manual
American DJ DJ Equipment Octo Beam User Manual
American Standard Hot Tub 0163060 User Manual
Apple MP3 Player MC903LL A User Manual
Axor Plumbing Product 04126XX0 User Manual
Bacharach Carbon Monoxide Alarm 24 9351 User Manual